dry casting polished surface Alumina Ceramic wheel roller
Reputation depends on quality, quality comes from Hard!
Alumina Ceramics:
Before using various plastic recycling methods to recycle waste plastics, most of them need to be sorted. Due to the many and complicated plastic consumption channels, some post-consumed plastics are difficult to distinguish by simple appearance. In the realm of plastic recycling methods, sorting waste plastics is a crucial step, often hindered by the complexity of plastic consumption channels leading to difficulties in visually distinguishing different plastic types. The Alumina Ceramic Disk offers a sustainable and practical alternative, with its innovative round structural design and advanced Alumina Zirconia Ceramic composition, providing a reliable and efficient means to streamline the recycling process while promoting environmental consciousness.
Therefore, it is best to indicate the material variety on the plastic products. China has formulated GB/T16288-2008 "Plastic Packaging Product Recycling Mark" with reference to the material variety marking proposed and implemented by the American Plastics Association (SPE). Although the above marking method can be used to facilitate sorting, there are still many unmarked labels in China. In order to separate different types of plastics for sorting and recycling, we must first master the knowledge of identifying different plastics. The following describes the simple identification method for plastics: general thermoplastics are crystalline and amorphous. The appearance of crystalline plastic is translucent, milky or opaque, and it is transparent only in the film state, and its hardness ranges from soft to horny. Amorphous is generally colorless, fully transparent when no additives are added, and the hardness is from harder than horny rubber (additives such as plasticizers are often added at this time). Thermosetting plastics usually contain fillers and are opaque, such as transparent without fillers. The elastomer has a rubber-like feel and has a certain stretch rate. The first thing is to look at it, because dark colored pigments are generally very toxic, so in general, the darker the color, the more toxic the plastic. Another very important reason for dyeing plastic is that the raw material is waste plastic, in order to cover up the original color. The second is smell. As long as the plastic has a peculiar smell, it is absolutely not allowed to store food anyway. The peculiar smell is generally the taste of additives, colorings and other additives or residual monomers added to the product. The third is to touch. The plastic that holds food generally feels smooth and shiny. If it doesn’t feel smooth, especially if it’s sticky, it must not be filled with food, because there are too many additives in it, and you can’t even imagine it. Accounted for more than 50%.
properties: High hardness, high strength, wear resistance, corrosion resistance, high temperacture (1600°), good thermal diffusivity, good insulativity, low cost etc.
Data Sheet↓
Color: White/Ivory Density: 3.9g/cm3 Alumina Content: 96% 99% 99.5% Gas permeability: 0 Water Absorption: 0 MONS' Hardness: 82 Vickers Hardness (Hv50): 15.7(1600) Gpa(Kg/mm²) Flexural Strength(20°C): 330Mpa Compressive Strength(20°C): 2000Mpa Fracture Toughness (20°C): 4 MPam1/2 Thermal Conductivity(20°C): 27.5W(m.K) Thermal Expansion Coefficient: 7.6 10-6/°C Thermal Shock Resistance: 200 △T°C
Maximum use temperature 1650°C
Dielectric Strength: ＞10 KV/mm
Dielectric Constant: 9.1er
Dielectric Loss Angle(1MHz): 0.0002-0.0003
Volume Resistivity(20°C): ＞1014Ω.cm
Application industry: Machinery, electronic, chemical, petroleum etc. Specific application: Electrical ceramic substrate, plunger, sealing ring etc.
Why Choose Us? 1.12 years of professional production industrial ceramics factory 2.High quality products with low price 3.High precision parts with lowest tolerance 4.Short time for production 5.Has a group of experienced, professional and efficient R&D team 6.Has a good reputation in China and abroad. 7.MOQ is not limited, small quantity is welcome.
8.Vigorous team and good after-sales service
Products Show
FAQ
Q: Are you trading company or manufacturer ?
A: We are factory.
Q: How long is your delivery time?
A: Generally it is 5-10 days if the goods are in stock. or it is 15-30 days if the goods are not in stock, it is according to quantity.
Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: What is your terms of payment ?
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 50% T/T in advance ,balance before shippment.
